Rtl_433 - Program To Decode Radio Transmissions From Devices On The ISM Bands (And Other Frequencies)


rtl_433 (despite the name) is a generic data receiver, mainly for the 433.92 MHz, 868 MHz (SRD), 315 MHz, 345 MHz, and 915 MHz ISM bands.

The official source code is in the https://github.com/merbanan/rtl_433/ repository. For more documentation and related projects see the https://triq.org/ site.

It works with RTL-SDR and/or SoapySDR. Actively tested and supported are Realtek RTL2832 based DVB dongles (using RTL-SDR) and LimeSDR (LimeSDR USB and LimeSDR mini engineering samples kindly provided by MyriadRf), PlutoSDR, HackRF One (using SoapySDR drivers), as well as SoapyRemote.


Building / Installation

rtl_433 is written in portable C (C99 standard) and known to compile on Linux (also embedded), MacOS, and Windows systems. Older compilers and toolchains are supported as a key-goal. Low resource consumption and very few dependencies allow rtl_433 to run on embedded hardware like (repurposed) routers. Systems with 32-bit i686 and 64-bit x86-64 as well as (embedded) ARM, like the Raspberry Pi and PlutoSDR are well supported.

See BUILDING.md

On Debian (sid) or Ubuntu (19.10+), apt-get install rtl-433 for other distros check https://repology.org/project/rtl-433/versions

On FreeBSD, pkg install rtl-433.

On MacOS, brew install rtl_433.

Docker images with rtl_433 are available on the github page of hertzg.


How to add support for unsupported sensors

See CONTRIBUTING.md.


Running
rtl_433 -h
analysis and decode attempt. Disable all decoders with -R 0 if you want analyzer output only. [-y <code>] Verify decoding of demodulated test data (e.g. "{25}fb2dd58") with enabled devices = File I/O options = [-S none | all | unknown | known] Signal auto save. Creates one file per signal. Note: Saves raw I/Q samples (uint8 pcm, 2 channel). Preferred mode for generating test files. [-r <filename> | help] Read data from input file instead of a receiver [-w <filename> | help] Save data stream to output file (a '-' dumps samples to stdout) [-W <filename> | help] Save data stream to output file, overwrite existing file = Data output options = [-F kv | json | csv | mqtt | influx | syslog | null | help] Produce decoded output in given format. Append output to file with :<filename> (e.g. -F csv:log.csv), defaults to stdout. Specify host/port for syslog with e.g. -F syslog:127.0.0.1:1514 [-M time[:<options>] | protocol | level | noise[:secs] | stats | bits | help] Add various meta data to each output. [-K FILE | PATH | <tag> | <key>=<tag>] Add an expanded token or fixed tag to every output line. [-C native | si | customary] Convert units in decoded output. [-n <value>] Specify number of samples to take (each sample is an I/Q pair) [-T <seconds>] Specify number of seconds to run, also 12:34 or 1h23m45s [-E hop | quit] Hop/Quit after outputting successful event(s) [-h] Output this usage help and exit Use -d, -g, -R, -X, -F, -M, -r, -w, or -W without argument for more help = Supported device protocols = [01] Silvercrest Remote Control [02] Rubicson Temperature Sensor [03] Prologue, FreeTec NC-7104, NC-7159-675 temperature sensor [04] Waveman Switch Transmitter [06]* ELV EM 1000 [07]* ELV WS 2000 [08] LaCrosse TX Temperature / Humidity Sensor [10]* Acurite 896 Rain Gauge [11] Acurite 609TXC Temperature and Humidity Sensor [12] Oregon Scientific Weather Sensor [13]* Mebus 433 [14]* Intertechno 433 [15] KlikAanKlikUit Wireless Switch [16] AlectoV1 Weather Sensor (Alecto WS3500 WS4500 Ventus W155/W044 Oregon) [17] Cardin S466-TX2 [18] Fine Offset Electronics, WH2, WH5, Telldus Temperature/Humidity/Rain Sensor [19] Nexus, FreeTec NC-7345, NX-3980, Solight TE82S, TFA 30.3209 temperature/humidity sensor [20] Ambient Weather, TFA 30.3208.02 temperature sensor [21] Calibeur RF-104 Sensor [22] X10 RF [23] DSC Security Contact [24]* Brennenstuhl RCS 2044 [25] Globaltronics GT-WT-02 Sensor [26] Danfoss CFR Thermostat [29] Chuango Security Technology [30] Generic Remote SC226x EV1527 [31] TFA-Twin-Plus-30.3049, Conrad KW9010, Ea2 BL999 [32] Fine Offset Electronics WH1080/WH3080 Weather Station [33] WT450, WT260H, WT405H [34] LaCrosse WS-2310 / WS-3600 Weather Station [35] Esperanza EWS [36] Efergy e2 classic [37]* Inovalley kw9015b, TFA Dostmann 30.3161 (Rain and temperature sensor) [38] Generic temperature sensor 1 [39] WG-PB12V1 Temperature Sensor [40] Acurite 592TXR Temp/Humidity, 5n1 Weather Station, 6045 Lightning, 3N1, Atlas [41] Acurite 986 Refrigerator / Freezer Thermometer [42] HIDEKI TS04 Temperature, Humidity, Wind and Rain Sensor [43] Watchman Sonic / Apollo Ultrasonic / Beckett Rocket oil tank monitor [44] CurrentCost Current Sensor [45] emonTx OpenEnergyMonitor [46] HT680 Remote control [47] Conrad S3318P, FreeTec NC-5849-913 temperature humidity sensor [48] Akhan 100F14 remote keyless entry [49] Quhwa [50] OSv1 Temperature Sensor [51] Proove / Nexa / KlikAanKlikUit Wireless Switch [52] Bresser Thermo-/Hygro-Sensor 3CH [53] Springfield Temperature and Soil Moisture [54] Oregon Scientific SL109H Remote Thermal Hygro Sensor [55] Acurite 606TX Temperature Sensor [56] TFA pool temperature sensor [57] Kedsum Temperature & Humidity Sensor, Pearl NC-7415 [58] Blyss DC5-UK-WH [59] Steelmate TPMS [60] Schrader TPMS [61]* LightwaveRF [62]* Elro DB286A Doorbell [63] Efergy Optical [64]* Honda Car Key [67] Radiohead ASK [68] Kerui PIR / Contact Sensor [69] Fine Offset WH1050 Weather Station [70] Honeywell Door/Window Sensor, 2Gig DW10/DW11, RE208 repeater [71] Maverick ET-732/733 BBQ Sensor [72]* RF-tech [73] LaCrosse TX141-Bv2, TX141TH-Bv2, TX141-Bv3, TX141W, TX145wsdth sensor [74] Acurite 00275rm,00276rm Temp/Humidity with optional probe [75] LaCrosse TX35DTH-IT, TFA Dostmann 30.3155 Temperature/Humidity sensor [76] LaCrosse TX29IT, TFA Dostmann 30.3159.IT Temperature sensor [77] Vaillant calorMatic VRT340f Central Heating Control [78] Fine Offset Electronics, WH25, WH32B, WH24, WH65B, HP1000 Temperature/Humidity/Pressure Sensor [79] Fine Offset Electronics, WH0530 Temperature/Rain Sensor [80] IBIS beacon [81] Oil Ultrasonic STANDARD FSK [82] Citroen TPMS [83] Oil Ultrasonic STANDARD ASK [84] Thermopro TP11 Thermometer [85] Solight TE44/TE66, EMOS E0107T, NX-6876-917 [86] Wireless Smoke and Heat Detector GS 558 [87] Generic wireless motion sensor [88] Toyota TPMS [89] Ford TPMS [90] Renault TPMS [91] inFactory, nor-tec, FreeTec NC-3982-913 temperature humidity sensor [92] FT-004-B Temperature Sensor [93] Ford Car Key [94] Philips outdoor temperature sensor (type AJ3650) [95] Schrader TPMS EG53MA4, PA66GF35 [96] Nexa [97] Thermopro TP08/TP12/TP20 thermometer [98] GE Color Effects [99] X10 Security [100] Interlogix GE UTC Security Devices [101]* Dish remote 6.3 [102] SimpliSafe Home Security System (May require disabling automatic gain for KeyPad decodes) [103] Sensible Living Mini-Plant Moisture Sensor [104] Wireless M-Bus, Mode C&T, 100kbps (-f 868950000 -s 1200000) [105] Wireless M-Bus, Mode S, 32.768kbps (-f 868300000 -s 1000000) [106]* Wireless M-Bus, Mode R, 4.8kbps (-f 868330000) [107]* Wireless M-Bus, Mode F, 2.4kbps [108] Hyundai WS SENZOR Remote Temperature Sensor [109] WT0124 Pool Thermometer [110] PMV-107J (Toyota) TPMS [111] Emos TTX201 Temperature Sensor [112] Ambient Weather TX-8300 Temperature/Humidity Sensor [113] Ambient Weather WH31E Thermo-Hygrometer Sensor, EcoWitt WH40 rain gauge [114] Maverick et73 [115] Honeywell ActivLink, Wireless Doorbell [116] Honeywell ActivLink, Wireless Doorbell (FSK) [117]* ESA1000 / ESA2000 Energy Monitor [118]* Biltema rain gauge [119] Bresser Weather Center 5-in-1 [120]* Digitech XC-0324 temperature sensor [121] Opus/Imagintronix XT300 Soil Moisture [122]* FS20 [123]* Jansite TPMS Model TY02S [124] LaCrosse/ELV/Conrad WS7000/WS2500 weather sensors [125] TS-FT002 Wireless Ultrasonic Tank Liquid Level Meter With Temperature Sensor [126] Companion WTR001 Temperature Sensor [127] Ecowitt Wireless Outdoor Thermometer WH53/WH0280/WH0281A [128] DirecTV RC66RX Remote Control [129]* Eurochron temperature and humidity sensor [130] IKEA Sparsnas Energy Meter Monitor [131] Microchip HCS200 KeeLoq Hopping Encoder based remotes [132] TFA Dostmann 30.3196 T/H outdoor sensor [133] Rubicson 48659 Thermometer [134] Holman Industries iWeather WS5029 weather station (newer PCM) [135] Philips outdoor temperature sensor (type AJ7010) [136] ESIC EMT7110 power meter [137] Globaltronics QUIGG GT-TMBBQ-05 [138] Globaltronics GT-WT-03 Sensor [139] Norgo NGE101 [140] Elantra2012 TPMS [141] Auriol HG02832, HG05124A-DCF, Rubicson 48957 temperature/humidity sensor [142] Fine Offset Electronics/ECOWITT WH51 Soil Moisture Sensor [143] Holman Industries iWeather WS5029 weather station (older PWM) [144] TBH weather sensor [145] WS2032 weather station [146] Auriol AFW2A1 temperature/humidity sensor [147] TFA Drop Rain Gauge 30.3233.01 [148] DSC Security Contact (WS4945) [149] ERT Standard Consumption Message (SCM) [150]* Klimalogg [151] Visonic powercode [152] Eurochron EFTH-800 temperature and humidity sensor [153] Cotech 36-7959 wireless weather station with USB [154] Standard Consumption Message Plus (SCMplus) [155] Fine Offset Electronics WH1080/WH3080 Weather Station (FSK) [156] Abarth 124 Spider TPMS [157] Missil ML0757 weather station [158] Sharp SPC775 weather station [159] Insteon [160] ERT Interval Data Message (IDM) [161] ERT Interval Data Message (IDM) for Net Meters [162]* ThermoPro-TX2 temperature sensor [163] Acurite 590TX Temperature with optional Humidity [164] Security+ 2.0 (Keyfob) [165] TFA Dostmann 30.3221.02 T/H Outdoor Sensor [166] LaCrosse Technology View LTV-WSDTH01 Breeze Pro Wind Sensor [167] Somfy RTS [168] Schrader TPMS SMD3MA4 (Subaru) [169]* Nice Flor-s remote control for gates [170] LaCrosse Technology View LTV-WR1 Multi Sensor [171] LaCrosse Technology View LTV-TH Thermo/Hygro Sensor [172] Bresser Weather Center 6-in-1, 7-in-1 indoor, new 5-in-1, 3-in-1 wind gauge, Froggit WH6000, Ventus C8488A [173] Bresser Weather Center 7-in-1 [174] EcoDHOME Smart Socket and MCEE Solar monitor [175] LaCrosse Technology View LTV-R1 Rainfall Gauge [176] BlueLine Power Monitor [177] Burnhard BBQ thermometer [178] Security+ (Keyfob) [179] Cavius smoke, heat and water detector [180] Jansite TPMS Model Solar [181] Amazon Basics Meat Thermometer [182] TFA Marbella Pool Thermometer [183] Auriol AHFL temperature/humidity sensor [184] Auriol AFT 77 B2 temperature sensor [185] Honeywell CM921 Wireless Programmable Room Thermostat [186] Hyundai TPMS (VDO) [187] RojaFlex shutter and remote devices [188] Marlec Solar iBoost+ sensors [189] Somfy io-homecontrol [190] Ambient Weather (Fine Offset) WH31L Lightning-Strike sensor * Disabled by default, use -R n or -G = Input device selection = RTL-SDR device driver is available. [-d <RTL-SDR USB device index>] (default: 0) [-d :<RTL-SDR USB device serial (can be set with rtl_eeprom -s)>] To set gain for RTL-SDR use -g <gain> to set an overall gain in dB. SoapySDR device driver is available. [-d ""] Open default SoapySDR device [-d driver=rtlsdr] Open e.g. specific SoapySDR device To set gain for SoapySDR use -g ELEM=val,ELEM=val,... e.g. -g LNA=20,TIA=8,PGA=2 (for LimeSDR). [-d rtl_tcp[:[//]host[:port]] (default: localhost:1234) Specify host/port to connect to with e.g. -d rtl_tcp:127.0.0.1:1234 = Gain option = [-g <gain>] (default: auto) For RTL-SDR: gain in dB ("0" is auto). For SoapySDR: gain in dB for automatic distribution ("" is auto), or string of gain elements. E.g. "LNA=20,TIA=8,PGA=2" for LimeSDR. = Flex decoder spec = Use -X <spec> to add a flexible general purpose decoder. <spec> is "key=value[,key=value...]" Common keys are: name=<name> (or: n=<name>) modulation=<modulation> (or: m=<modulation>) short=<short> (or: s=<short>) long=<long> (or: l=<long>) sync=<sync> (or: y=<sync>) reset=<reset> (or: r=<reset>) gap=<gap> (or: g=<gap>) tolerance=<tolerance> (or: t=<tolerance>) where: <name> can be any descriptive name tag you need in the output <modulation> is one of: OOK_MC_ZEROBIT : Manchester Code with fixed leading zero bit OOK_PCM : Pulse Code Modulation (RZ or NRZ) OOK_PPM : Pulse Position Modulation OOK_PWM : Pulse Width Modulation OOK_DMC : Differential Manchester Code OOK_PIWM_RAW : Raw Pulse Interval and Width Modulation OOK_PIWM_DC : Differential Pulse Interval and Width Modulation OOK_MC_OSV1 : Manchester Code for OSv1 devices FSK_PCM : FSK Pulse Code Modulation FSK_PWM : FSK Pulse Width Modulation FSK_MC_ZEROBIT : Manchester Code with fixed leading zero bit <short>, <long>, <sync> are nominal modulation timings in us, <reset>, <gap>, <tolerance> are maximum modulation timings in us: PCM short: Nominal width of pulse [us] long: Nominal width of bit period [us] PPM short: Nominal width of '0' gap [us] long: Nominal width of '1' gap [us] PWM short: Nominal width of '1' pulse [us] long: Nominal width of '0' pulse [us] sync: Nominal width of sync pulse [us] (optional) common gap: Maximum gap size before new row of bits [us] reset: Maximum gap size before End Of Message [us] tolerance: Maximum pulse deviation [us] (optional). Available options are: bits=<n> : only match if at least one row has <n> bits rows=<n> : only match if there are <n> rows repeats=<n> : only match if some row is repeated <n> times use opt>=n to match at least <n> and opt<=n to match at most <n> invert : invert all bits reflect : reflect each byte (MSB first to MSB last) match=<bits> : only match if the <bits> are found preamble=<bits> : match and align at the <bits> preamble <bits> is a row spec of {<bit count>}<bits as hex number> unique : suppress duplicate row output countonly : suppress detailed row output E.g. -X "n=doorbell,m=OOK_PWM,s=400,l=800,r=7000,g=1000,match={24}0xa9878c,repeats>=3" = Output format option = [-F kv|json|csv|mqtt|influx|syslog|null] Produce decoded output in given format. Without this option the default is KV output. Use "-F null" to remove the default. Append output to file with :<filename> (e.g. -F csv:log.csv), defaults to stdout. Specify MQTT server with e.g. -F mqtt://localhost:1883 Add MQTT options with e.g. -F "mqtt://host:1883,opt=arg" MQTT options are: user=foo, pass=bar, retain[=0|1], <format>[=topic] Supported MQTT formats: (default is all) events: posts JSON event data states: posts JSON state data devices: posts device and sensor info in nested topics The topic string will expand keys like [/model] E.g. -F "mqtt://localhost:1883,user=USERNAME,pass=PASSWORD,retain=0,devices=rtl_433[/id]" With MQTT each rtl_433 instance needs a distinct driver selection. The MQTT Client-ID is computed from the driver string. If you use multiple RTL-SDR, perhaps set a serial and select by that (helps not to get the wrong antenna). Specify InfluxDB 2.0 server with e.g. -F "influx://localhost:9999/api/v2/write?org=<org>&bucket=<bucket>,token=<authtoken>" Specify InfluxDB 1.x server with e.g. -F "influx://localhost:8086/write?db=<db>&p=<password>&u=<user>" Additional parameter -M time:unix:usec:utc for correct timestamps in InfluxDB recommended Specify host/port for syslog with e.g. -F syslog:127.0.0.1:1514 = Meta information option = [-M time[:<options>]|protocol|level|noise[:<secs>]|stats|bits] Add various metadata to every output line. Use "time" to add current date and time meta data (preset for live inputs). Use "time:rel" to add sample position meta data (preset for read-file and stdin). Use "time:unix" to show the seconds since unix epoch as time meta data. Use "time:iso" to show the time with ISO-8601 format (YYYY-MM-DD"T"hh:mm:ss). Use "time:off" to remove time meta data. Use "time:usec" to add microseconds to date time meta data. Use "time:tz" to output time with timezone offset. Use "time:utc" to output time in UTC. (this may also be accomplished by invocation with TZ environment variable set). "usec" and "utc" can be combined with other options, eg. "time:unix:utc:usec". Use "protocol" / "noprotocol" to output the decoder protocol number meta data. Use "level" to add Modulation, Frequency, RSSI, SNR, and Noise meta data. Use "noise[:secs]" to report estimated noise level at intervals (default: 10 seconds). Use "stats[:[<level>][:<interval>]]" to report statistics (default: 600 seconds). level 0: no report, 1: report successful devices, 2: report active devices, 3: report all Use "bits" to add bit representation to code outputs (for debug). = Read file option = [-r <filename>] Read data from input file instead of a receiver Parameters are detected from the full path, file name, and extension. A center frequency is detected as (fractional) number suffixed with 'M', 'Hz', 'kHz', 'MHz', or 'GHz'. A sample rate is detected as (fractional) number suffixed with 'k', 'sps', 'ksps', 'Msps', or 'Gsps'. File content and format are detected as parameters, possible options are: 'cu8', 'cs16', 'cf32' ('IQ' implied), and 'am.s16'. Parameters must be separated by non-alphanumeric chars and are case-insensitive. Overrides can be prefixed, separated by colon (':') E.g. default detection by extension: path/filename.am.s16 forced overrides: am:s16:path/filename.ext Reading from pipes also support format options. E.g reading complex 32-bit float: CU32:- = Write file option = [-w <filename>] Save data stream to output file (a '-' dumps samples to stdout) [-W <filename>] Save data stream to output file, overwrite existing file Parameters are detected from the full path, file name, and extension. File content and format are detected as parameters, possible options are: 'cu8', 'cs8', 'cs16', 'cf32' ('IQ' implied), 'am.s16', 'am.f32', 'fm.s16', 'fm.f32', 'i.f32', 'q.f32', 'logic.u8', 'ook', and 'vcd'. Parameters must be separated by non-alphanumeric chars and are case-insensitive. Overrides can be prefixed, separated by colon (':') E.g. default detection by extension: path/filename.am.s16 forced overrides: am:s16:path/filename.ext ">

= General options =
[-V] Output the version string and exit
[-v] Increase verbosity (can be used multiple times).
-v : verbose, -vv : verbose decoders, -vvv : debug decoders, -vvvv : trace decoding).
[-c <path>] Read config options from a file
= Tuner options =
[-d <RTL-SDR USB device index> | :<RTL-SDR USB device serial> | <SoapySDR device query> | rtl_tcp | help]
[-g <gain> | help] (default: auto)
[-t <settings>] apply a list of keyword=value settings for SoapySDR devices
e.g. -t "antenna=A,bandwidth=4.5M,rfnotch_ctrl=false"
[-f <frequency>] Receive frequency(s) (default: 433920000 Hz)
[-H <seconds>] Hop interval for polling of multiple frequencies (default: 600 seconds)
[-p <ppm_error] Correct rtl-sdr tuner frequency offset error (default: 0)
[-s <sample rate>] Set sample rate (default: 250000 Hz)
= Demodulato r options =
[-R <device> | help] Enable only the specified device decoding protocol (can be used multiple times)
Specify a negative number to disable a device decoding protocol (can be used multiple times)
[-G] Enable blacklisted device decoding protocols, for testing only.
[-X <spec> | help] Add a general purpose decoder (prepend -R 0 to disable all decoders)
[-Y auto | classic | minmax] FSK pulse detector mode.
[-Y level=<dB level>] Manual detection level used to determine pulses (-1.0 to -30.0) (0=auto).
[-Y minlevel=<dB level>] Manual minimum detection level used to determine pulses (-1.0 to -99.0).
[-Y minsnr=<dB level>] Minimum SNR to determine pulses (1.0 to 99.0).
[-Y autolevel] Set minlevel automatically based on average estimated noise.
[-Y squelch] Skip frames below estimated noise level to reduce cpu load.
[-Y ampest | magest] Choose amplitude or magnitude level estimator .
= Analyze/Debug options =
[-a] Analyze mode. Print a textual description of the signal.
[-A] Pulse Analyzer. Enable pulse analysis and decode attempt.
Disable all decoders with -R 0 if you want analyzer output only.
[-y <code>] Verify decoding of demodulated test data (e.g. "{25}fb2dd58") with enabled devices
= File I/O options =
[-S none | all | unknown | known] Signal auto save. Creates one file per signal.
Note: Saves raw I/Q samples (uint8 pcm, 2 channel). Preferred mode for generating test files.
[-r <filename> | help] Read data from input file instead of a receiver
[-w <filename> | help] Save data stream to output file (a '-' dumps samples to stdout)
[-W <filename> | help] Save data stream to output file, overwrite existing file
= Data output options =
[-F kv | json | csv | mqtt | influx | syslog | null | help] Produce decoded output in given format.
App end output to file with :<filename> (e.g. -F csv:log.csv), defaults to stdout.
Specify host/port for syslog with e.g. -F syslog:127.0.0.1:1514
[-M time[:<options>] | protocol | level | noise[:secs] | stats | bits | help] Add various meta data to each output.
[-K FILE | PATH | <tag> | <key>=<tag>] Add an expanded token or fixed tag to every output line.
[-C native | si | customary] Convert units in decoded output.
[-n <value>] Specify number of samples to take (each sample is an I/Q pair)
[-T <seconds>] Specify number of seconds to run, also 12:34 or 1h23m45s
[-E hop | quit] Hop/Quit after outputting successful event(s)
[-h] Output this usage help and exit
Use -d, -g, -R, -X, -F, -M, -r, -w, or -W without argument for more help



= Supported device protocols =
[01] Silvercrest Remote Control
[02] Rubicson Temperature Sensor
[03] Prolo gue, FreeTec NC-7104, NC-7159-675 temperature sensor
[04] Waveman Switch Transmitter
[06]* ELV EM 1000
[07]* ELV WS 2000
[08] LaCrosse TX Temperature / Humidity Sensor
[10]* Acurite 896 Rain Gauge
[11] Acurite 609TXC Temperature and Humidity Sensor
[12] Oregon Scientific Weather Sensor
[13]* Mebus 433
[14]* Intertechno 433
[15] KlikAanKlikUit Wireless Switch
[16] AlectoV1 Weather Sensor (Alecto WS3500 WS4500 Ventus W155/W044 Oregon)
[17] Cardin S466-TX2
[18] Fine Offset Electronics, WH2, WH5, Telldus Temperature/Humidity/Rain Sensor
[19] Nexus, FreeTec NC-7345, NX-3980, Solight TE82S, TFA 30.3209 temperature/humidity sensor
[20] Ambient Weather, TFA 30.3208.02 temperature sensor
[21] Calibeur RF-104 Sensor
[22] X10 RF
[23] DSC Security Contact
[24]* Brennenstuhl RCS 2044
[25] Globaltronics GT-WT-02 Sensor
[26] Danfoss CFR Thermostat
[29] Chuango Security Technology
[30] Generic Remote SC226x EV1527
[31] TFA-Twin-Plus-30.3049, Conrad KW9010, Ea2 BL999
[32] Fine Offset Electronics WH1080/WH3080 Weather Station
[33] WT450, WT260H, WT405H
[34] LaCrosse WS-2310 / WS-3600 Weather Station
[35] Esperanza EWS
[36] Efergy e2 classic
[37]* Inovalley kw9015b, TFA Dostmann 30.3161 (Rain and temperature sensor)
[38] Generic temperature sensor 1
[39] WG-PB12V1 Temperature Sensor
[40] Acurite 592TXR Temp/Humidity, 5n1 Weather Station, 6045 Lightning, 3N1, Atlas
[41] Acurite 986 Refrigerator / Freezer Thermometer
[42] HIDEKI TS04 Temperature, Humidity, Wind and Rain Sensor
[43] Watchman Sonic / Apollo Ultrasonic / Beckett Rocket oil tank monitor
[44] CurrentCost Current Sensor
[45] emonTx OpenEnergyMonitor
[46] HT680 Remote control
[47] Conrad S3318P, FreeTec NC-5849-913 temperature humidity sensor
[48] Akhan 100F14 remote keyless entry
[49] Quhwa
[50] OSv1 Temperature Sensor
[51] Proove / Nexa / KlikAanKlikUit Wireless Switch
[52] Bresser Thermo-/Hygro-Sensor 3CH
[53] Springfield Temperature and Soil Moisture
[54] Oregon Scientific SL109H Remote Thermal Hygro Sensor
[55] Acurite 606TX Temperature Sensor
[56] TFA pool temperature sensor
[57] Kedsum Temperature & Humidity Sensor, Pearl NC-7415
[58] Blyss DC5-UK-WH
[59] Steelmate TPMS
[60] Schrader TPMS
[61]* LightwaveRF
[62]* Elro DB286A Doorbell
[63] Efergy Optical
[64]* Honda Car Key
[67] Radiohead ASK
[68] Kerui PIR / Contact Sensor
[69] Fine Offset WH1050 Weather Station
[70] Honeywell Door/Window Sensor, 2Gig DW10/DW11, RE208 repeater
[71] Maverick ET-732/733 BBQ Sensor
[72]* RF-tech
[73] LaCrosse TX141-Bv2, TX141TH-Bv2, TX141-Bv3, TX141W, TX145wsdth sensor
[74] Acurite 00275rm,00276rm Temp/Humidity with optional probe
[75] LaCrosse TX35DTH-IT, TFA Dostmann 30.3155 Temperature/Humidity sensor
[76] LaCrosse TX29IT, TFA Dostmann 30.3159.IT Temperature sensor
[77] Vaillant calorMatic VRT340f Central Heating Control
[78] Fine Offset Electronics, WH25, WH32B, WH24, WH65B, HP1000 Temperature/Humidity/Pressure Sensor
[79] Fine Offset Electronics, WH0530 Temperature/Rain Sensor
[80] IBIS beacon
[81] Oil Ultrasonic STANDARD FSK
[82] Citroen TPMS
[83] Oil Ultrasonic STANDARD ASK
[84] Thermopro TP11 Thermometer
[85] Solight TE44/TE66, EMOS E0107T, NX-6876-917
[86] Wireless Smoke and Heat Detector GS 558
[87] Generic wireless motion sensor
[88] Toyota TPMS
[89] Ford TPMS
[90] Renau lt TPMS
[91] inFactory, nor-tec, FreeTec NC-3982-913 temperature humidity sensor
[92] FT-004-B Temperature Sensor
[93] Ford Car Key
[94] Philips outdoor temperature sensor (type AJ3650)
[95] Schrader TPMS EG53MA4, PA66GF35
[96] Nexa
[97] Thermopro TP08/TP12/TP20 thermometer
[98] GE Color Effects
[99] X10 Security
[100] Interlogix GE UTC Security Devices
[101]* Dish remote 6.3
[102] SimpliSafe Home Security System (May require disabling automatic gain for KeyPad decodes)
[103] Sensible Living Mini-Plant Moisture Sensor
[104] Wireless M-Bus, Mode C&T, 100kbps (-f 868950000 -s 1200000)
[105] Wireless M-Bus, Mode S, 32.768kbps (-f 868300000 -s 1000000)
[106]* Wireless M-Bus, Mode R, 4.8kbps (-f 868330000)
[107]* Wireless M-Bus, Mode F, 2.4kbps
[108] Hyundai WS SENZOR Remote Temperature Sensor
[109] WT0124 Pool Thermom eter
[110] PMV-107J (Toyota) TPMS
[111] Emos TTX201 Temperature Sensor
[112] Ambient Weather TX-8300 Temperature/Humidity Sensor
[113] Ambient Weather WH31E Thermo-Hygrometer Sensor, EcoWitt WH40 rain gauge
[114] Maverick et73
[115] Honeywell ActivLink, Wireless Doorbell
[116] Honeywell ActivLink, Wireless Doorbell (FSK)
[117]* ESA1000 / ESA2000 Energy Monitor
[118]* Biltema rain gauge
[119] Bresser Weather Center 5-in-1
[120]* Digitech XC-0324 temperature sensor
[121] Opus/Imagintronix XT300 Soil Moisture
[122]* FS20
[123]* Jansite TPMS Model TY02S
[124] LaCrosse/ELV/Conrad WS7000/WS2500 weather sensors
[125] TS-FT002 Wireless Ultrasonic Tank Liquid Level Meter With Temperature Sensor
[126] Companion WTR001 Temperature Sensor
[127] Ecowitt Wireless Outdoor Thermometer WH53/WH0280/WH0281A
[128] DirecTV RC66RX Remote Con trol
[129]* Eurochron temperature and humidity sensor
[130] IKEA Sparsnas Energy Meter Monitor
[131] Microchip HCS200 KeeLoq Hopping Encoder based remotes
[132] TFA Dostmann 30.3196 T/H outdoor sensor
[133] Rubicson 48659 Thermometer
[134] Holman Industries iWeather WS5029 weather station (newer PCM)
[135] Philips outdoor temperature sensor (type AJ7010)
[136] ESIC EMT7110 power meter
[137] Globaltronics QUIGG GT-TMBBQ-05
[138] Globaltronics GT-WT-03 Sensor
[139] Norgo NGE101
[140] Elantra2012 TPMS
[141] Auriol HG02832, HG05124A-DCF, Rubicson 48957 temperature/humidity sensor
[142] Fine Offset Electronics/ECOWITT WH51 Soil Moisture Sensor
[143] Holman Industries iWeather WS5029 weather station (older PWM)
[144] TBH weather sensor
[145] WS2032 weather station
[146] Auriol AFW2A1 temperature/humidity sensor
[147] TFA Drop Rain Gauge 30.3233.01
[148] DSC Security Contact (WS4945)
[149] ERT Standard Consumption Message (SCM)
[150]* Klimalogg
[151] Visonic powercode
[152] Eurochron EFTH-800 temperature and humidity sensor
[153] Cotech 36-7959 wireless weather station with USB
[154] Standard Consumption Message Plus (SCMplus)
[155] Fine Offset Electronics WH1080/WH3080 Weather Station (FSK)
[156] Abarth 124 Spider TPMS
[157] Missil ML0757 weather station
[158] Sharp SPC775 weather station
[159] Insteon
[160] ERT Interval Data Message (IDM)
[161] ERT Interval Data Message (IDM) for Net Meters
[162]* ThermoPro-TX2 temperature sensor
[163] Acurite 590TX Temperature with optional Humidity
[164] Security+ 2.0 (Keyfob)
[165] TFA Dostmann 30.3221.02 T/H Outdoor Sensor
[166] LaCrosse Technology View LTV-WSDTH01 Breeze Pro Wind Sensor
[167] Somfy RTS
[168] Schrader TPMS SMD3MA4 (Subaru)
[169]* Nice Flor-s remote control for gates
[170] LaCrosse Technology View LTV-WR1 Multi Sensor
[171] LaCrosse Technology View LTV-TH Thermo/Hygro Sensor
[172] Bresser Weather Center 6-in-1, 7-in-1 indoor, new 5-in-1, 3-in-1 wind gauge, Froggit WH6000, Ventus C8488A
[173] Bresser Weather Center 7-in-1
[174] EcoDHOME Smart Socket and MCEE Solar monitor
[175] LaCrosse Technology View LTV-R1 Rainfall Gauge
[176] BlueLine Power Monitor
[177] Burnhard BBQ thermometer
[178] Security+ (Keyfob)
[179] Cavius smoke, heat and water detector
[180] Jansite TPMS Model Solar
[181] Amazon Basics Meat Thermometer
[182] TFA Marbella Pool Thermometer
[183] Auriol AHFL temperature/humidity sensor
[184] Auriol AFT 77 B2 temperature sensor
[185] Honeywell CM921 Wireless Programmable Room Ther mostat
[186] Hyundai TPMS (VDO)
[187] RojaFlex shutter and remote devices
[188] Marlec Solar iBoost+ sensors
[189] Somfy io-homecontrol
[190] Ambient Weather (Fine Offset) WH31L Lightning-Strike sensor

* Disabled by default, use -R n or -G


= Input device selection =
RTL-SDR device driver is available.
[-d <RTL-SDR USB device index>] (default: 0)
[-d :<RTL-SDR USB device serial (can be set with rtl_eeprom -s)>]
To set gain for RTL-SDR use -g <gain> to set an overall gain in dB.
SoapySDR device driver is available.
[-d ""] Open default SoapySDR device
[-d driver=rtlsdr] Open e.g. specific SoapySDR device
To set gain for SoapySDR use -g ELEM=val,ELEM=val,... e.g. -g LNA=20,TIA=8,PGA=2 (for LimeSDR).
[-d rtl_tcp[:[//]host[:port]] (default: localhost:1234)
Specify host/port to connect to with e.g. -d rtl_tcp:127.0.0.1:1234


= Gain o ption =
[-g <gain>] (default: auto)
For RTL-SDR: gain in dB ("0" is auto).
For SoapySDR: gain in dB for automatic distribution ("" is auto), or string of gain elements.
E.g. "LNA=20,TIA=8,PGA=2" for LimeSDR.


= Flex decoder spec =
Use -X <spec> to add a flexible general purpose decoder.

<spec> is "key=value[,key=value...]"
Common keys are:
name=<name> (or: n=<name>)
modulation=<modulation> (or: m=<modulation>)
short=<short> (or: s=<short>)
long=<long> (or: l=<long>)
sync=<sync> (or: y=<sync>)
reset=<reset> (or: r=<reset>)
gap=<gap> (or: g=<gap>)
tolerance=<tolerance> (or: t=<tolerance>)
where:
<name> can be any descriptive name tag you need in the output
<modulation> is one of:
OOK_MC_ZEROBIT : Manchester Code with fixed leading zero bit
OOK_PCM : Pulse Code Modulation (RZ or NRZ)
OOK_PPM : Pulse Position Modulation
OOK_PWM : Pulse Width Modulation
OOK_DMC : Differential Manchester Code
OOK_PIWM_RAW : Raw Pulse Interval and Width Modulation
OOK_PIWM_DC : Differential Pulse Interval and Width Modulation
OOK_MC_OSV1 : Manchester Code for OSv1 devices
FSK_PCM : FSK Pulse Code Modulation
FSK_PWM : FSK Pulse Width Modulation
FSK_MC_ZEROBIT : Manchester Code with fixed leading zero bit
<short>, <long>, <sync> are nominal modulation timings in us,
<reset>, <gap>, <tolerance> are maximum modulation timings in us:
PCM short: Nominal width of pulse [us]
long: Nominal width of bit period [us]
PPM short: Nominal width of '0' gap [us]
long: Nominal width of '1' gap [us]
PWM short: Nominal width of '1' pulse [us]
long: Nominal w idth of '0' pulse [us]
sync: Nominal width of sync pulse [us] (optional)
common gap: Maximum gap size before new row of bits [us]
reset: Maximum gap size before End Of Message [us]
tolerance: Maximum pulse deviation [us] (optional).
Available options are:
bits=<n> : only match if at least one row has <n> bits
rows=<n> : only match if there are <n> rows
repeats=<n> : only match if some row is repeated <n> times
use opt>=n to match at least <n> and opt<=n to match at most <n>
invert : invert all bits
reflect : reflect each byte (MSB first to MSB last)
match=<bits> : only match if the <bits> are found
preamble=<bits> : match and align at the <bits> preamble
<bits> is a row spec of {<bit count>}<bits as hex number>
unique : suppress duplicate row output

countonly : suppress detailed row o utput

E.g. -X "n=doorbell,m=OOK_PWM,s=400,l=800,r=7000,g=1000,match={24}0xa9878c,repeats>=3"



= Output format option =
[-F kv|json|csv|mqtt|influx|syslog|null] Produce decoded output in given format.
Without this option the default is KV output. Use "-F null" to remove the default.
Append output to file with :<filename> (e.g. -F csv:log.csv), defaults to stdout.
Specify MQTT server with e.g. -F mqtt://localhost:1883
Add MQTT options with e.g. -F "mqtt://host:1883,opt=arg"
MQTT options are: user=foo, pass=bar, retain[=0|1], <format>[=topic]
Supported MQTT formats: (default is all)
events: posts JSON event data
states: posts JSON state data
devices: posts device and sensor info in nested topics
The topic string will expand keys like [/model]
E.g. -F "mqtt://localhost:1883,user=USERNAME,pass=PASSWORD,retain=0,devices=rtl_433[/id]"
With MQTT each rtl_433 instance needs a d istinct driver selection. The MQTT Client-ID is computed from the driver string.
If you use multiple RTL-SDR, perhaps set a serial and select by that (helps not to get the wrong antenna).
Specify InfluxDB 2.0 server with e.g. -F "influx://localhost:9999/api/v2/write?org=<org>&bucket=<bucket>,token=<authtoken>"
Specify InfluxDB 1.x server with e.g. -F "influx://localhost:8086/write?db=<db>&p=<password>&u=<user>"
Additional parameter -M time:unix:usec:utc for correct timestamps in InfluxDB recommended
Specify host/port for syslog with e.g. -F syslog:127.0.0.1:1514


= Meta information option =
[-M time[:<options>]|protocol|level|noise[:<secs>]|stats|bits] Add various metadata to every output line.
Use "time" to add current date and time meta data (preset for live inputs).
Use "time:rel" to add sample position meta data (preset for read-file and stdin).
Use "time:un ix" to show the seconds since unix epoch as time meta data.
Use "time:iso" to show the time with ISO-8601 format (YYYY-MM-DD"T"hh:mm:ss).
Use "time:off" to remove time meta data.
Use "time:usec" to add microseconds to date time meta data.
Use "time:tz" to output time with timezone offset.
Use "time:utc" to output time in UTC.
(this may also be accomplished by invocation with TZ environment variable set).
"usec" and "utc" can be combined with other options, eg. "time:unix:utc:usec".
Use "protocol" / "noprotocol" to output the decoder protocol number meta data.
Use "level" to add Modulation, Frequency, RSSI, SNR, and Noise meta data.
Use "noise[:secs]" to report estimated noise level at intervals (default: 10 seconds).
Use "stats[:[<level>][:<interval>]]" to report statistics (default: 600 seconds).
level 0: no report, 1: report successful devices, 2: report active devices, 3: report all
Use "bits" to add bit representation to code outputs (for debug).


= Read file option =
[-r <filename>] Read data from input file instead of a receiver
Parameters are detected from the full path, file name, and extension.

A center frequency is detected as (fractional) number suffixed with 'M',
'Hz', 'kHz', 'MHz', or 'GHz'.

A sample rate is detected as (fractional) number suffixed with 'k',
'sps', 'ksps', 'Msps', or 'Gsps'.

File content and format are detected as parameters, possible options are:
'cu8', 'cs16', 'cf32' ('IQ' implied), and 'am.s16'.

Parameters must be separated by non-alphanumeric chars and are case-insensitive.
Overrides can be prefixed, separated by colon (':')

E.g. default detection by extension: path/filename.am.s16
forced overrides: am:s16:path/filename.ext

Reading from pipes also support format options.
E.g reading complex 32-bit float: CU32:-


= Write file option =
[-w <filename>] Save data stream to output file (a '-' dumps samples to stdout)
[-W <filename>] Save data stream to output file, overwrite existing file
Parameters are detected from the full path, file name, and extension.

File content and format are detected as parameters, possible options are:
'cu8', 'cs8', 'cs16', 'cf32' ('IQ' implied),
'am.s16', 'am.f32', 'fm.s16', 'fm.f32',
'i.f32', 'q.f32', 'logic.u8', 'ook', and 'vcd'.

Parameters must be separated by non-alphanumeric chars and are case-insensitive.
Overrides can be prefixed, separated by colon (':')

E.g. default detection by extension: path/filename.am.s16
forced overrides: am:s16:path/filename.ext

Some examples:

Command Description
rtl_433 Default receive mode, use the first device found, listen at 433.92 MHz at 250k sample rate.
rtl_433 -C si Default receive mode, also convert units to metric system.
rtl_433 -f 868M -s 1024k Listen at 868 MHz and 1024k sample rate.
rtl_433 -M hires -M level Report microsecond accurate timestamps and add reception levels (depending on gain).
rtl_433 -R 1 -R 8 -R 43 Enable only specific decoders for desired devices.
rtl_433 -A Enable pulse analyzer. Summarizes the timings of pulses, gaps, and periods. Can be used with -R 0 to disable decoders.
rtl_433 -S all -T 120 Save all detected signals (g###_###M_###k.cu8). Run for 2 minutes.
rtl_433 -K FILE -r file_name Read a saved data file instead of receiving live data. Tag output with filenames.
rtl_433 -F json -M utc | mosquitto_pub -t home/rtl_433 -l Will pipe the output to network as JSON formatted MQTT messages. A test MQTT client can be found in examples/mqtt_rtl_433_test_client.py.
rtl_433 -f 433.53M -f 434.02M -H 15 Will poll two frequencies with 15 seconds hop interval.

Google Group

Join the Google group, rtl_433, for more information about rtl_433: https://groups.google.com/forum/#!forum/rtl_433


Troubleshooting

If you see this error:

Kernel driver is active, or device is claimed by second instance of librtlsdr.
In the first case, please either detach or blacklist the kernel module
(dvb_usb_rtl28xxu), or enable automatic detaching at compile time.

then

sudo rmmod dvb_usb_rtl28xxu rtl2832

Releases

Version numbering scheme used is year.month. We try to keep the API compatible between releases but focus is on maintainablity.



Rtl_433 - Program To Decode Radio Transmissions From Devices On The ISM Bands (And Other Frequencies) Rtl_433 - Program To Decode Radio Transmissions From Devices On The ISM Bands (And Other Frequencies) Reviewed by Zion3R on 8:30 AM Rating: 5